1. Pick an unblemished coconut shell with no noticeable cracks. The beautiful thing about using a coconut shell to make a bowl is that you can make a bowl of any size. For a smaller bowl, simply pick a smaller coconut. For a larger bowl, grab a bigger one.
If there are cracks, they’ll just get larger and more pronounced as you smooth and sand the shell.
2. Drain the liquid from the coconut and split it in half. Grab a bowl, a cutting board, a hammer, and a screwdriver. Tap the screwdriver through the eyes of the coconut and drain the liquid into the bowl.
Then, strike the coconut with the hammer all the way around its hemisphere until a crack starts to form. Keep hammering the coconut until the crack is large enough for you to pull the coconut apart.
3. Pry the coconut meat away from the shell so the inside is smooth.
This sounds harder than it is! Wedge a butter knife between the shell and the coconut meat and wiggle it back and forth until the meat begins to come away from the shell. It might take a while to do the entire coconut, but it’s an essential part of the process.
Be careful while doing this. Try holding the coconut shell in your non-dominant hand so you can wield the butter knife with more control.
4. Remove the fibrous exterior of the coconut with 80-grit sandpaper.
If possible, attach a sanding flap wheel to a drill to make the process go faster—it can take quite a while to sand the shell down by hand. Make sure to wear a dust mask and gloves while you work! If you don’t have a drill and sanding flap wheel, a few other alternatives are listed below for you:
- Use a hand sander to protect your hands from the sandpaper’s grit.
- Rub the exterior of the shell with steel wool if you don’t have sandpaper.
- Use a lathe and sanding attachment for an even quicker process.
5. Sand the exterior of the shell by hand to a smooth finish. Hold the shell in a gloved hand so that if the sandpaper slips, it won’t rough up your skin. Since you already used 80-grit sandpaper, move on to something higher, like 100-grit for the first pass-over. Continue using finer and finer grits of sandpaper until ending at 240-grit.
For example, you could go from 100-grit to 120-grit to 240-grit.
The goal is to expose the smooth, polished shell beneath the fibrous exterior.
6. Rub the edge of the shell over 40-grit sandpaper to even it out. The edge of your coconut shell might not be completely even and might have a few jagged sections. Place a piece of 40-grit sandpaper on your workstation, place the shell cut-side-down on it, and rub it back and forth until the edge is smooth to the touch.
This process makes your bowls look much more professional and polished once they’re done.
7. Sketch your design on the outside of the shell so it’s easy to follow. You can always freestyle your carvings, but if you want something intricate, it’s best to follow an outline. Use a pencil or pen—basically anything that will be visible without permanently marring the shell's surface.[12] You could also print a design on paper and tape it to the outside of the shell. If you do this, take a precision knife and cut the paper away in the spots you want the shell carved. In this way, you make your own stencil.
Keep in mind that coconut shells are really thin. You may not be able to carve it the same way you might traditionally carve a piece of wood.
Think about using small holes to create different designs, like swirls, geometric patterns, or even faces or words.
8. Use a power drill or dremel to carve your bowl’s design. With a dremel, you can usually carve a design into the shell without going all the way through. Just be conscious of how deep you’re carving, so you don’t accidentally break through. Use a small bit on a drill to make delicate holes through the shell.
9. Add decorative elements to the edge of the shells with a file. For example, file a “V” shape into the edge of the shell every 2 to 3 inches (5.1 to 7.6 cm) to resemble flower petals.[15] You can use flat, rounded, circular, or triangular files on a coconut shell. Be careful working with metal files. They can be very sharp!
10. Paint your bowls with acrylic paint if you want to add color to them. Acrylic paint is an excellent choice for coconut shells because it dries quickly.
11. Polish your carved bowls with beeswax for a natural shine. Put a little beeswax on a clean rag and rub it all over the shell. Reapply wax to the rag when it gets dry, and continue buffing the shell until it has an even shine all over. You can reapply beeswax as needed to keep your carved shell looking nice.
12. Apply a coat of varnish if you want your bowls to have a glossy finish. Use a clear varnish if you want the shell’s color to shine through, or use a colored varnish for a deeper shine. Let the varnish dry completely before moving the shell. If the shell is to hold food or drink, don’t apply varnish or wax on the inside. Do this step in a well-ventilated area. Varnish can produce some pretty strong fumes!
Dry your bowls in the sun until they’re no longer tacky. The heat from the sun will help the wax or varnish dry faster. Once the bowls are no longer sticky or tacky to the touch, you can move them.
